Investing in Pianos can be very expensive and for this reason, they should be kept in their best condition always. If proper care is not taken, the equipment will spoil and then you will need another musical instruments whose market rate is very high, as well. When you have taken all caution possible, and they have been damaging, you do not have to worry. The Riverside Piano Refinishing technique will be of help to you.

The Refinishing is done in the following step. You will start by eliminating the old varnish and stains completely. This is done through a process known as stripping. This is to be done after the hardware has been removed and put in bags. Ensure you label these packages well for humble times when you are putting the parts back to their places.

Having the correct protective gear is necessary. This will include the gloves that will keep your hands safe. You will also need a mask to avoid breathing in fumes that will be harmful to your health.

Stripping should be done in an airy place to lessen the fumes emitted. You will need to remove the varnish and then the paint. Make sure you do not use water-based stripping mixtures because wood takes in water, in plenty and if it is soaked, it damages the instrument.

The second step will be renovating any repairs on the instrument. You will rectify dents, scratches and nicks that are usually caused by the stripping you had earlier done. These repairs can be done effectively using the two methods that are as follows.

There is the technique that uses steam. It involves using small levels of steam that rise the wood and refills the dented areas that could be on the instrument. This method is complex, and it needs to be done by a very skilled person to avoid ruining the surface of the device.

The second one uses of fillers. These fillers help to cover the broken parts. You should choose the ones that have similar chemical components like the varnish and stain that you intend to use during the finishing process. This will raise the chances of you are doing it right. This technique just like the one of using steam requires a competent person to perform it up to your expectations. Do a proper search to identify the best in the city and then get them to do the job for you.

The finishing process concludes the refinish exercise. This includes procedures done on the instrument with the varnish. The popular varnishes are shellac, lacquer and polyurethane. The experts prefer using the nitrocellulose lacquer. This need several coats as one may brush off the excess one until the right limit is reached. In each of the application intervals, there should be some time left for it to dry so that the wood is not scratched, and the outcome will be a smooth and glossy surface. These processes demand a lot of labor and special skills hence hire an expert who understands this job well. This is what can give you the desired outcomes and also value for your money.

The Methods Applied For Riverside Piano Refinishing

The high piano quality has a very high market price. So care should be taken to avoid damaging them. Though sometimes they can get damaged, and the good news is that they can be refinished. By doing this, you will be restoring it to its original state. There are three processes used in Riverside Piano Refinishing technique as explained below.

The first step is to remove all the old varnish and stain through the stripping process. Before you do this, you have to remove all the hardware and place each part in its own bag. These bags have to be labeled for easy identification when you will be putting them back together. Then keep them safe for later.

It is important to have proper protective gear like gloves to protect your hands. A mask should also be worn to avoid inhaling the fumes when working. For this process to be successful and easier, you will need paint strippers, plastic scrapers or steel wool and a thinner to remove the layers of paint or varnish.

The area where stripping is done has to be well ventilated to reduce the fumes produced. The Process starts by removing the varnish first then the stain using a paint stripper though you should not use a water-based stripping solution. This is because wood absorbs water, and if it seeps through the cracks it can cause more damage to the instrument. After this is done, you can wash the stripped surface using a thinner as you check if any stain has been left.

The next process is to repair the damage on the instrument. After proper removal of stain and cleaning is done, you need to repair damages on the instrument such as scratches, dents, or even nicks that you may have caused in the initial process of stripping. There are two methods you can use to repair these damages.

The first method involves the use of steam. Small amounts of steam can be used to make the wood rise and refill any dented places on the surface of the instrument. This procedure requires a lot of skills and if not done properly it can ruin the surface of the instrument.

The other technique is by use of fillers that help to seal the damaged parts. It is necessary to select filler that is of the same chemical make up as a stain and varnish you will use for the finishing process. If the chemical makeup does not match, it can cause a reaction on the color which will be used to stain, hence the surface will be uneven. After this number of stain coats are applied using a cotton rag or foam brush. It should be rubbed in thoroughly while wiping away the excess stain to avoid streaking.

The last process is to finish the instrument using a varnish. The commonly used ones are shellac, polyurethane and lacquer. Professionals prefer to use nitrocellulose lacquer, and if you choose it, then you will need to apply a number of coats as you rub out the excess until the proper limit is met. Each interval of application should be left to cure to prevent scratching of the wood so that you can achieve a smooth glossy surface. These processes require a person to be very keen and are very labor intensive. For a person who does not have the proper experience it is advisable to seek help from piano refinishing firms who have packages that suit your need.

A Clear Explanation of The Riverside Piano Refinishing Process.

In the city, many people love musical instruments. Some of them will purchase them for playing, and others will buy them for sentimental purposes. They are so costly, especially the high quality ones. For this reason, they should always get the best care. In case you identify any fault on your appliance, it is proper to call a specialist to come fix it. You will also need the Riverside Piano Refinishing technique to enhance its performance.

To start this method, is the stripping process which is very important. It helps in getting rid of the old varnish and stains. This should be done after the hardware has been packed well in its bags to create order and also keep the instrument safe.

During this exercise, the workers you have hired must follow instructions of their profession. Among the things they must do, is to wear protective gears. Ensure that they have their gloves, masks and the other necessary garments on, to keep them safe from any harm.

Before the stripping starts, you must ensure that there is adequate ventilation in the room. This is to minimize the amount of fumes released during the process. The stripped surface will require a thinner to check whether some stain is still there.

After this step, it is followed by making the necessary repairs. Make sure all the damages on the device are rectified. This will include taking care of the scratches, dents, as well as the nicks that result from the stripping.

There two methods that will be used to do the renovation are as follows. The very first one is the one that makes use of steam. This task can be so difficult, and only skilled experts can do it right. It requires the steam is applied to the wood causing it to rise and then it will refill the scratched places on the instrument surface.

The other common technique is the use of fillers. This is used to seal the broken parts. A chemical used to make the filler that you prefer should be the same as the one in the varnish and stains that you will apply in the finishing process. After the procedure is needed, you will need several stain coats applied on the surface. This can be done by use of cotton rag and the foam brush. Ensure it is polished thoroughly to wipe out the stain that is in excess to prevent the equipment from streaking.

The last thing that will be done is applying the varnish. You can choose from the shellac, lacquer and polyurethane types. The Professional you will hire will advise you on which one is suitable for your case. The most preferred is the nitrocellulose lacquer. It usually requires many coats applied because the excess paint has to be removed till the limit reached. Ensure that you have someone who understands this whole process of piano refinishing to work for you. Of same significance, make sure that you select a package that will satisfy you and the one that you can comfortably afford.

CLICK BUTTON TO ORDER NOW